Mobile Home Electrical Installation
in Spring Hill, FL
Licensed, Local, and Trusted Since 1973 (#EC13006813)
Faulkner Electric installs, upgrades, and repairs electrical systems in mobile and manufactured homes. Whether you're setting up a new home on a lot, replacing an aging panel, or rewiring after a failed inspection, our licensed electricians handle the full job — from the meter base and service disconnect to the branch circuits, outlets, and grounding. Mobile homes carry their own set of rules and hazards that standard residential work doesn't cover, and we work to those standards every time. Customers choose us because we show up when we say we will, quote before we start, and leave a system that passes inspection and keeps power flowing safely.
Why Mobile Home Wiring Is Different
Manufactured homes aren't wired like site-built houses. They're built to HUD standards, use factory-installed feeder systems, and have tight spaces beneath and behind walls that limit how conductors can run. A few differences matter on every job:
- Service and feeder setup. Most mobile homes are fed from a separate service pole or pedestal, not from a panel mounted directly on the home. That means a service disconnect at the pole, a feeder run to the home, and a main distribution panel inside.
- Grounding and bonding. The neutral and ground must be separated at the mobile home's panel, with grounding and bonding handled at the service equipment on the pole. Getting this wrong is one of the most common inspection failures we see.
- Cramped access. Wiring runs under the home and through narrow chases. Conductors need protection from physical damage, moisture, and rodents.
- Load demand. Older units were often built for far less demand than modern appliances, HVAC, and electronics require, so panels and circuits frequently need upsizing.
Our Mobile Home Electrical Services
- New service installation — service pole, meter base, disconnect, and feeder to the home for a new setup or relocation.
- Panel upgrades and replacement — swapping undersized or failing panels for properly rated distribution panels with modern breakers.
- Whole-home rewiring — replacing aluminum branch wiring, damaged conductors, or wiring that no longer meets code.
- Outlet, switch, and circuit work — adding GFCI protection in kitchens, baths, and exterior locations, plus dedicated circuits for large appliances.
- Grounding and bonding corrections — fixing the neutral/ground separation and grounding electrode system.
- Smoke and carbon monoxide detectors — installing and wiring life-safety devices where they're required.
- Troubleshooting and repair — tracking down tripping breakers, dead outlets, flickering lights, and burnt connections.
How We Hook Up Electricity to a Mobile Home
Every installation follows the same disciplined process so nothing gets missed:
Assessment. We review your home's age, appliances, and existing wiring, then calculate the load to determine the right service size — commonly 100 or 200 amps.
Service equipment. We set or verify the meter base, service disconnect, and grounding at the pole or pedestal.
Feeder run. We run the four-conductor feeder (two hots, a neutral, and a separate ground) from the service disconnect to the home's panel, protected where required.
Panel and circuits. We install or upgrade the distribution panel inside the home, keeping neutrals and grounds separated, and land each branch circuit on its correct breaker.
Devices and protection. We install outlets, GFCI and AFCI protection where code calls for it, and life-safety detectors.
Testing and inspection. We test every circuit, verify grounding, and coordinate the inspection so your system is signed off and energized.
Materials and Code Compliance
The right materials are what separate a system that lasts from one that fails early. We use conductors rated for the load and environment, weatherproof fittings for anything exposed to the elements, and protection for wiring that runs under the home where it's exposed to moisture and physical damage. GFCI protection goes in kitchens, bathrooms, laundry areas, and outdoor receptacles. Grounding and bonding are verified at the service equipment, and the neutral is isolated at the home's panel. Every job is built to meet the electrical code and the specific requirements that apply to manufactured housing, which is exactly what an inspector will be checking.
Mistakes to Avoid With DIY Mobile Home Wiring
Bonding the neutral and ground at the home's panel. On a feeder-fed mobile home, this practice creates parallel current paths and a shock hazard.
Undersizing the service. Running a modern home on an old, small panel leads to nuisance trips and overheated conductors.
Leaving wiring unprotected under the home. Exposed conductors get chewed, crushed, and soaked.
Skipping GFCI and smoke/CO devices. These aren't optional, they're required and they save lives.
Reusing damaged or corroded connections. Loose and burnt terminals are a leading cause of electrical fires.
Any of these will fail an inspection at best and cause a fire at worst. Electrical work on a mobile home service is not a safe place to guess.
Why Choose Faulkner Electric
Our electricians work on mobile and manufactured homes regularly, so we know the code sections, the common failure points, and the shortcuts previous installers took that you're now paying for. Here's what you get with us:
- Licensed, insured electricians who work to code and coordinate inspections.
- Clear quotes before work begins — you approve the scope and price up front.
- Work that passes inspection the first time, so you're not paying for callbacks and re-inspections.
- Straight answers about what your home needs and what it doesn't, so you're not sold work you don't require.
Frequently Asked Questions (FAQ)
How much does it cost to hook up a mobile home to electricity?
The cost depends on how much of the service you need built. A basic hookup involves the meter base, service disconnect, feeder run, and panel connection. Costs climb with higher amperage, longer distances between the service pole and the home, trenching for underground feeders, and any grounding work. The best way to get an accurate figure is a site assessment — we'll look at your setup and give you a written quote before any work starts.
Does wire under a mobile home need to be in conduit?
Wiring run under a mobile home has to be protected from physical damage and the elements. Depending on the type of cable and where it runs, that protection is provided by conduit or by using cable rated and supported for the location. Exposed conductors that could be crushed, chewed, or exposed to moisture must be in a raceway. We install every under-home run to meet code so it holds up and passes inspection.
How do you hook up electricity to a mobile home?
Power comes from a service pole or pedestal fitted with a meter base and a service disconnect. From there, a four-wire feeder — two hot conductors, a neutral, and a separate equipment ground — runs to the distribution panel inside the home. Grounding and bonding are handled at the service equipment, and the neutral stays separated from the ground at the home's panel. After the branch circuits are landed and tested, the system is inspected and energized. This is service-level work that should be done by a licensed electrician.
How much does it cost to have an electrician rewire a mobile home?
Rewiring cost is driven by the size of the home, how many circuits and devices are involved, whether the panel is being replaced at the same time, and how accessible the existing wiring is. Replacing older aluminum branch wiring or wiring damaged by moisture or rodents adds labor. We provide a written estimate after inspecting the home so you know exactly what the job involves and what it will cost.
Why does my mobile home keep tripping breakers?
Frequent tripping usually points to an overloaded circuit, an undersized panel, a damaged conductor, or a loose or corroded connection. On older homes it often means the electrical system can't keep up with modern appliance loads. We troubleshoot the cause rather than just resetting the breaker, and recommend the fix — which may be a dedicated circuit, a repair, or a panel upgrade.
How Do I Get My Mobile Home Wired Right?
Whether you're setting up a new home, upgrading a tired panel, or fixing wiring that won't pass inspection, Faulkner Electric will get it done safely and to code. Call us today or request a free quote, and we'll assess your home, explain your options, and give you a clear price before any work begins.
Installing Ceiling Fans Throughout West Central Florida
Faulkner Electric installs ceiling fans across 22+ communities in West Central Florida:
Spring Hill · Brooksville · Hudson · New Port Richey · Trinity · Land O Lakes · Wesley Chapel · Tarpon Springs · Palm Harbor · Lutz · Dade City · Zephyrhills · Holiday · Homosassa · Crystal River · Inverness · Hernando · Odessa · New Tampa · Dunedin · Safety Harbor · Clearwater
Not sure if we cover your area? Call us at
(727) 301-7996 and we'll confirm.
